192.168.100.1 Router| IP Address Login, Default Username & Password Wifi

The default gateway address is 192.168.100.1; this post will discuss the IP address login and the default username and password. Let’s investigate 192.168.100.1 with PowerPacPlus in this article.

About 192.168.100.1 IP Address

An IP address is used to uniquely identify any network. There are both public and private versions of it. Since a device is accessible to everyone online, its public router IP address is used to identify it.

The majority of manufacturers utilize 192.168.100.1 as one of the router admin IP addresses that are used the most frequently. The IP numbers 10.0.0.1 and 192.168.0.1 are also frequently used to log into routers. Simply input the IP address to gain administrative access to your home router.

Using the IP address 192.168.100.1, you can access the router’s administrative interface and change the network configurations. You can change the router’s configuration, the DNS settings, or default settings like the login and password. Using Myfiosgateway as a login, setup, and management tool will allow you to manage the basic Wi-Fi network settings.

How To Login 192.168.100.1?

Follow these steps to access the 192.168.100.1 admin panel settings:

  • Open a new tab in your browser.
  • After typing http://192.168.100.1 or 192.168.100.1, press Enter.192.168.100.1
  • The login page for the router will appear.
  • The usual username and password should be entered. (Administrator username; Administrator password)
  • Your login has been successful so far.

List Of Default Router Username And Password

Because the address 192.168.100.1 consists entirely of digits and not any English characters, such as the small L in the IP 192.168.”l”00.1, users may accidentally write it as 192.168.l00.1 which is wrong. These private IP addresses are assigned to the reachable devices in a local network and are a part of the IPv4 range. Routers may also receive the default IP address 192.168.100.1 in order to access the admin tools.

The most prevalent router brands, models, default IP addresses, usernames, and passwords are mentioned below; if your router’s brand or model isn’t listed, look up the full list of router default login credentials.

This list contains the most widely used default usernames and passwords for the device’s IP address, 192.168.100.1.

ROUTER BRAND DEFAULT IP ADDRESS USERNAME PASSWORD
2Wire 192.168.1.1 (none) Wireless
Asus 192.168.1.1 admin admin
Dell 192.168.1.1 admin password
Cisco 192.168.10.10 cisco cisco
D-Link 192.168.0.1 admin
Huawei 192.168.100.1 root root
Linksys 192.168.101.1 admin
Motorola 192.168.100.1 admin Motorola
Netgear 192.168.100.1 admin password
Planet 192.168.100.1 admin admin
SMC Networks 192.168.100.1 MO changeme
Zoom 192.168.100.1 admin password

Additionally, the PowerPacPlus provided the most popular router login table for 192.168.100.1 below will be a huge assistance to you.

192.168.100.1

Default Your WiFi Password And SSID

NETGEAR

192.168.100.1

  • Launch the web browser on your PC. (Be certain that your PC is connected to the NETGEAR Router.)
  • To log in, use the router’s default username and password. These are listed on a label that is attached to the back of the router.
  • Open a new tab, and in the address bar, type http://192.168.100.1
  • Select Basic Wireless from the menu bar after logging in.
  • Enter the new Wi-Fi SSID in the Name (SSID) box.
  • Enter the new Wi-Fi password in the Password (Network Key) field, then click Apply to save the changes.
  • The Wi-Fi SSID and password for the NETGEAR Router will be changed.

TP-Link

192.168.100.1
  • Open a web browser on a PC connected to the TP-Link Router. Step two is to go to http://192.168.100.1
  • the login page for a TP-Link router.
  • Log in to your TP-Link router with the usual credentials.
  • After login in, choose Wireless > Wireless Settings.
  • Click on 6, then enter the new Wi-Fi SSID in the Wireless Network Name box. saving modifications.
  • From the menu, select Wireless Security.
  • The new WiFi password should be entered in the Password box under the WPA/WPA2 Encryption section.
  • Click Save to keep the changes.
  • The Wi-Fi SSID and password for the TP-Link router will be accurately modified.

Huawei

192.168.100.1
  • You should start a web browser on your machine. Make sure your computer is connected to the IndiHome Huawei Router.
  • Open a new browser tab and navigate to http://192.168.100.1
  • Here is the login page for Huawei routers. Enter your login details here to log in.
  • After logging in, go to Settings WLAN WLAN Basic Settings.
  • Enter the new Wi-Fi SSID into the SSID box.
  • Enter the new password in the WPA pre-shared key field.
  • Click Apply to save the changes.
  • Now that the SSID and password have been modified.

Forgot Your Username Or Password For 192.168.100.1

Everyone has encountered the difficulty of being unable to log in due to forgetting their login, password, or both. Don’t worry if you lose or forget your login information for 192.168.100.1. You may easily retrieve it.

In order to recover the forgotten username and password, you would have to reset your router to its default settings. Keep in mind that any changes you make will be reversed.

  • Grab a paperclip or something with a sharp point.
  • Find the little RESET button on the router’s rear.
  • Press and hold that button with the needle or paperclip for 10 to 15 seconds.
  • After that, let go of the button. When the router reboots itself, all settings, including any altered login and password, will be restored to their original state.

Some Problems And Troubleshooting

Cannot Access The Admin Page

Has your device been properly connected to the Internet? Examine them carefully to ensure that everything is in working order.

The wrong IP address is yet another common problem that most people encounter. It’s easy to enter the incorrect IP address because the numbers can occasionally seem complicated. Be careful because they all look the same; you might have accidentally substituted the letter l for the number 1. You can miss a few of them if you don’t check the dots as well.

Fail To Login

If you experience this issue, you must utilize a Linksys router and set the default gateway to 192.168.100.1 as soon as possible.

  • One of the most common methods to find out what your router utilizes is to open the Windows terminal.
  • To open the Windows terminal, click the search icon (the magnifying glass icon on the Windows 10 taskbar) and type “cmd” before pressing Enter.
  • The Windows terminal is displayed. Now type “ipconfig.”
  • Check your default gateway’s IP address.
  • If you are unable to access this page and the IP address is still 192.168.100.1 After that, the router needs to be reset.
  • Your router has a physical “reset” button that you can press to restart it. The Linksys router has a red-colored reset button.

Important information: The reset button must be depressed for roughly 10 seconds. Check to see if the router’s POWER led is flashing as you hold. It demonstrates that the router was correctly reset.

After that, try logging into your router once more using the 192.168.100.1 IP.

At first, you might find the 192.168.100.1 IP address confusing and annoying to use. But if you have any knowledge of it beforehand, we’re confident that you won’t have any trouble connecting to the IP address and resolving your Internet connection on your own.

Therefore, keep in mind the information PowerPacPlus gave above because you’ll need it in the future. We are more than pleased to help, so feel free to ask any questions.

FAQs

What is the default username and password for the 192.168.100.1 router?

Most routers often have “admin” and “password” as their default username and password, respectively. If none of these work, you can consult your router’s user manual or ask the manufacturer for help.

Can I use 192.168.100.1 to connect to my wifi?

The private IP address of your router, not your wifi network, is 192.168.100.1 in this case. You must enter the SSID (network name) and password in your device’s wifi settings in order to connect to your wifi network.

How do I change my WiFi password?

Use the router’s default username and password to log in and change your WiFi password. In the address bar, locate the “Wireless Security” settings, and then type your password. The changes must be saved for your new password to take effect.

Leave a Comment